Rev 576 |
Blame |
Compare with Previous |
Last modification |
View Log
| Download
| RSS feed
| ?url?
`include "../include/tune.v"
// Pentevo project (c) NedoPC 2008-2012
//
// top-level
module top(
// clocks
input fclk,
output clkz_out,
input clkz_in,
// z80
input iorq_n,
input mreq_n,
input rd_n,
input wr_n,
input m1_n,
input rfsh_n,
output int_n,
output nmi_n,
output wait_n,
output res,
inout [7:0] d,
input [15:0] a,
// zxbus and related
output csrom,
output romoe_n,
output romwe_n,
output rompg0_n,
output dos_n, // aka rompg1
output rompg2,
output rompg3,
output rompg4,
input iorqge1,
input iorqge2,
output iorq1_n,
output iorq2_n,
// DRAM
inout [15:0] rd,
output [9:0] ra,
output rwe_n,
output rucas_n,
output rlcas_n,
output rras0_n,
output rras1_n,
// video
output [1:0] vred,
output [1:0] vgrn,
output [1:0] vblu,
output vhsync,
output vvsync,
output vcsync,
// AY control and audio/tape
output ay_clk,
output ay_bdir,
output ay_bc1,
output beep,
// IDE
output [2:0] ide_a,
inout [15:0] ide_d,
output ide_dir,
input ide_rdy,
output ide_cs0_n,
output ide_cs1_n,
output ide_rs_n,
output ide_rd_n,
output ide_wr_n,
// VG93 and diskdrive
output vg_clk,
output vg_cs_n,
output vg_res_n,
output vg_hrdy,
output vg_rclk,
output vg_rawr,
output [1:0] vg_a, // disk drive selection
output vg_wrd,
output vg_side,
input step,
input vg_sl,
input vg_sr,
input vg_tr43,
input rdat_b_n,
input vg_wf_de,
input vg_drq,
input vg_irq,
input vg_wd,
// serial links (atmega-fpga, sdcard)
output sdcs_n,
output sddo,
output sdclk,
input sddi,
input spics_n,
input spick,
input spido,
output spidi,
output spiint_n
);
wire dos;
wire zclk; // z80 clock for short
wire zpos,zneg;
wire rst_n; // global reset
wire rrdy;
wire [15:0] rddata;
wire [4:0] rompg;
wire [7:0] zports_dout;
wire zports_dataout;
wire porthit;
wire [39:0] kbd_data;
wire [ 7:0] mus_data;
wire kbd_stb,mus_xstb,mus_ystb,mus_btnstb,kj_stb;
wire [ 4:0] kbd_port_data;
wire [ 4:0] kj_port_data;
wire [ 7:0] mus_port_data;
wire [7:0] wait_read,wait_write;
wire wait_rnw;
wire wait_start_gluclock;
wire wait_start_comport;
wire wait_end;
wire [7:0] gluclock_addr;
wire [2:0] comport_addr;
wire [6:0] waits;
// config signals
wire [7:0] not_used;
wire cfg_vga_on;
// nmi signals
wire gen_nmi;
wire clr_nmi;
wire in_nmi;
wire [1:0] set_nmi;
wire imm_nmi;
// breakpoint signals
wire brk_ena;
wire [15:0] brk_addr;
wire tape_in;
wire [15:0] ideout;
wire [15:0] idein;
wire idedataout;
wire [7:0] zmem_dout;
wire zmem_dataout;
reg [3:0] ayclk_gen;
wire [7:0] received;
wire [7:0] tobesent;
wire intrq,drq;
wire vg_wrFF;
assign zclk = clkz_in;
// RESETTER
wire genrst;
resetter myrst( .clk(fclk),
.rst_in_n(~genrst),
.rst_out_n(rst_n) );
defparam myrst.RST_CNT_SIZE = 6;
assign nmi_n=gen_nmi ? 1'b0 : 1'bZ;
assign res= ~rst_n;
assign ide_rs_n = rst_n;
assign ide_d = idedataout ? ideout : 16'hZZZZ;
assign idein = ide_d;
assign ide_dir = ~idedataout;
wire [7:0] peff7;
wire [7:0] p7ffd;
wire romrw_en;
wire cpm_n;
wire fnt_wr;
wire cpu_req,cpu_rnw,cpu_wrbsel,cpu_strobe;
wire [20:0] cpu_addr;
wire [15:0] cpu_rddata;
wire [7:0] cpu_wrdata;
wire cbeg,post_cbeg,pre_cend,cend;
wire go;
// AVR SDcard control
wire avr_lock_claim,
avr_lock_grant,
avr_sdcs_n,
avr_sd_start;
wire [7:0] avr_sd_datain;
wire [7:0] avr_sd_dataout;
// ZX SDcard control
wire zx_sdcs_n_val,
zx_sdcs_n_stb,
zx_sd_start;
wire [7:0] zx_sd_datain;
wire [7:0] zx_sd_dataout;
wire tape_read; // data for tapein
wire beeper_mux; // what is mixed to FPGA beeper output - beeper (0) or tapeout (1)
wire [2:0] atm_scr_mode;
wire atm_turbo;
wire beeper_wr, covox_wr;
wire [5:0] palcolor; // palette readback
wire [1:0] int_turbo;
wire cpu_next;
wire cpu_stall;
wire external_port;
//AY control
always @(posedge fclk)
begin
ayclk_gen <= ayclk_gen + 4'd1;
end
assign ay_clk = ayclk_gen[3];
// fix ATM2-style ROM addressing for PENT-like ROM layout.
// this causes compications when writing to the flashROM from Z80
// and need to split and re-build old ATM romfiles before burning in
// flash
// wire [1:0] adr_fix;
// assign adr_fix = ~{ rompg[0], rompg[1] };
// assign rompg0_n = ~adr_fix[0];
// assign dos_n = adr_fix[1];
// assign rompg2 = 1'b0;//rompg[2];
// assign rompg3 = 1'b0;//rompg[3];
// assign rompg4 = 1'b0;//rompg[4];
assign rompg0_n = ~rompg[0];
assign dos_n = rompg[1];
assign rompg2 = rompg[2];
assign rompg3 = rompg[3];
assign rompg4 = rompg[4];
wire [3:0] zclk_stall;
zclock zclock
(
.fclk(fclk), .rst_n(rst_n), .zclk(zclk), .rfsh_n(rfsh_n), .zclk_out(clkz_out),
.zpos(zpos), .zneg(zneg),
.turbo( {atm_turbo,~(peff7[4])} ), .pre_cend(pre_cend), .cbeg(cbeg),
.zclk_stall( cpu_stall | (|zclk_stall) ), .int_turbo(int_turbo),
.external_port(external_port), .iorq_n(iorq_n), .m1_n(m1_n)
);
wire [7:0] dout_ram;
wire ena_ram;
wire [7:0] dout_ports;
wire ena_ports;
wire [3:0] border;
wire drive_ff;
wire atm_palwr;
wire [5:0] atm_paldata;
wire [7:0] fontrom_readback;
wire int_start;
// data bus out: either RAM data or internal ports data or 0xFF with unused ports
assign d = ena_ram ? dout_ram : ( ena_ports ? dout_ports : ( drive_ff ? 8'hFF : 8'bZZZZZZZZ ) );
zbus zxbus( .iorq_n(iorq_n), .rd_n(rd_n), .wr_n(wr_n), .m1_n(m1_n),
.iorq1_n(iorq1_n), .iorq2_n(iorq2_n), .iorqge1(iorqge1), .iorqge2(iorqge2),
.porthit(porthit), .drive_ff(drive_ff) );
/////////////////////////////////////
// ATM memory pagers instantiation //
/////////////////////////////////////
wire pager_off;
wire pent1m_ROM;
wire [ 5:0] pent1m_page;
wire pent1m_ram0_0;
wire pent1m_1m_on;
wire atmF7_wr_fclk;
wire [3:0] dos_turn_off,
dos_turn_on;
wire [ 7:0] page [0:3];
wire [ 3:0] romnram;
// for reading back data via xxBE port
wire [ 7:0] rd_pages [0:7];
wire [ 7:0] rd_ramnrom;
wire [ 7:0] rd_dos7ffd;
generate
genvar i;
for(i=0;i<4;i=i+1)
begin : instantiate_atm_pagers
atm_pager #( .ADDR(i) )
atm_pager( .rst_n(rst_n),
.fclk (fclk),
.zpos (zpos),
.zneg (zneg),
.za(a),
.zd(d),
.mreq_n(mreq_n),
.rd_n (rd_n),
.m1_n (m1_n),
.pager_off(pager_off),
.pent1m_ROM (pent1m_ROM),
.pent1m_page (pent1m_page),
.pent1m_ram0_0(pent1m_ram0_0),
.pent1m_1m_on (pent1m_1m_on),
.in_nmi(in_nmi),
.atmF7_wr(atmF7_wr_fclk),
.dos(dos),
.dos_turn_on (dos_turn_on[i]),
.dos_turn_off(dos_turn_off[i]),
.zclk_stall(zclk_stall[i]),
.page (page[i]),
.romnram(romnram[i]),
.rd_page0 (rd_pages[i ]),
.rd_page1 (rd_pages[i+4]),
.rd_ramnrom( {rd_ramnrom[i+4], rd_ramnrom[i]} ),
.rd_dos7ffd( {rd_dos7ffd[i+4], rd_dos7ffd[i]} )
);
end
endgenerate
///////////////////////////
// DOS signal controller //
///////////////////////////
zdos zdos( .rst_n(rst_n),
.fclk(fclk),
.dos_turn_on ( |dos_turn_on ),
.dos_turn_off( |dos_turn_off ),
.cpm_n(cpm_n),
.dos(dos)
);
///////////////////////////
// Z80 memory controller //
///////////////////////////
zmem z80mem
(
.fclk (fclk ),
.rst_n(rst_n),
.zpos(zpos),
.zneg(zneg),
.cbeg (cbeg ),
.post_cbeg(post_cbeg),
.pre_cend (pre_cend ),
.cend (cend ),
.za (a ),
.zd_in (d ),
.zd_out(dout_ram),
.zd_ena(ena_ram ),
.m1_n (m1_n ),
.rfsh_n(rfsh_n ),
.iorq_n(iorq_n ),
.mreq_n(mreq_n ),
.rd_n (rd_n ),
.wr_n (wr_n ),
.win0_romnram(romnram[0]),
.win1_romnram(romnram[1]),
.win2_romnram(romnram[2]),
.win3_romnram(romnram[3]),
.win0_page(page[0]),
.win1_page(page[1]),
.win2_page(page[2]),
.win3_page(page[3]),
.romrw_en(romrw_en),
.rompg (rompg ),
.romoe_n(romoe_n),
.romwe_n(romwe_n),
.csrom (csrom ),
.cpu_req (cpu_req ),
.cpu_rnw (cpu_rnw ),
.cpu_wrbsel(cpu_wrbsel),
.cpu_strobe(cpu_strobe),
.cpu_addr (cpu_addr ),
.cpu_wrdata(cpu_wrdata),
.cpu_rddata(cpu_rddata),
.cpu_stall (cpu_stall ),
.cpu_next (cpu_next ),
.int_turbo(int_turbo)
);
wire [20:0] daddr;
wire dreq;
wire drnw;
wire [15:0] drddata;
wire [15:0] dwrdata;
wire [1:0] dbsel;
dram dram( .clk(fclk),
.rst_n(rst_n),
.addr(daddr),
.req(dreq),
.rnw(drnw),
.cbeg(cbeg),
.rrdy(drrdy),
.rddata(drddata),
.wrdata(dwrdata),
.bsel(dbsel),
.ra(ra),
.rd(rd),
.rwe_n(rwe_n),
.rucas_n(rucas_n),
.rlcas_n(rlcas_n),
.rras0_n(rras0_n),
.rras1_n(rras1_n)
);
wire [1:0] bw;
wire [20:0] video_addr;
wire [15:0] video_data;
wire video_strobe;
wire video_next;
arbiter dramarb( .clk(fclk),
.rst_n(rst_n),
.dram_addr(daddr),
.dram_req(dreq),
.dram_rnw(drnw),
.dram_cbeg(cbeg),
.dram_rrdy(drrdy),
.dram_bsel(dbsel),
.dram_rddata(drddata),
.dram_wrdata(dwrdata),
.post_cbeg(post_cbeg),
.pre_cend (pre_cend ),
.cend (cend ),
.go(go),
.bw(bw),
.video_addr(video_addr),
.video_data(video_data),
.video_strobe(video_strobe),
.video_next(video_next),
//.cpu_waitcyc(cpu_waitcyc),
.cpu_next (cpu_next),
.cpu_req(cpu_req),
.cpu_rnw(cpu_rnw),
.cpu_addr(cpu_addr),
.cpu_wrbsel(cpu_wrbsel),
.cpu_wrdata(cpu_wrdata),
.cpu_rddata(cpu_rddata),
.cpu_strobe(cpu_strobe) );
video_top video_top(
.clk(fclk),
.vred(vred),
.vgrn(vgrn),
.vblu(vblu),
.vhsync(vhsync),
.vvsync(vvsync),
.vcsync(vcsync),
.zxborder(border),
.pent_vmode( {peff7[0],peff7[5]} ),
.atm_vmode (atm_scr_mode),
.scr_page(p7ffd[3]),
.vga_on(cfg_vga_on),
.cbeg (cbeg ),
.post_cbeg(post_cbeg),
.pre_cend (pre_cend ),
.cend (cend ),
.video_go (go ),
.video_bw (bw ),
.video_addr (video_addr ),
.video_data (video_data ),
.video_strobe(video_strobe),
.video_next (video_next ),
.atm_palwr (atm_palwr ),
.atm_paldata(atm_paldata),
.int_start(int_start),
.fnt_a (a[10:0]),
.fnt_d (d ),
.fnt_wr(fnt_wr ),
.palcolor(palcolor),
.fontrom_readback(fontrom_readback)
);
slavespi slavespi(
.fclk(fclk), .rst_n(rst_n),
.spics_n(spics_n), .spidi(spidi),
.spido(spido), .spick(spick),
.status_in({/* wait_rnw */ wr_n, waits[6:0]}), .genrst(genrst),
.kbd_out(kbd_data),
.kbd_stb(kbd_stb), .mus_out(mus_data),
.mus_xstb(mus_xstb), .mus_ystb(mus_ystb),
.mus_btnstb(mus_btnstb), .kj_stb(kj_stb),
.gluclock_addr(gluclock_addr),
.comport_addr (comport_addr),
.wait_write(wait_write),
.wait_read(wait_read),
.wait_rnw(wait_rnw),
.wait_end(wait_end),
.config0( { not_used[7:4], beeper_mux, tape_read, set_nmi[0], cfg_vga_on} ),
.sd_lock_out(avr_lock_claim),
.sd_lock_in (avr_lock_grant),
.sd_cs_n (avr_sdcs_n ),
.sd_start (avr_sd_start ),
.sd_datain (avr_sd_datain ),
.sd_dataout (avr_sd_dataout)
);
zkbdmus zkbdmus( .fclk(fclk), .rst_n(rst_n),
.kbd_in(kbd_data), .kbd_stb(kbd_stb),
.mus_in(mus_data), .mus_xstb(mus_xstb),
.mus_ystb(mus_ystb), .mus_btnstb(mus_btnstb),
.kj_stb(kj_stb), .kj_data(kj_port_data),
.zah(a[15:8]), .kbd_data(kbd_port_data),
.mus_data(mus_port_data)
);
zports zports( .zclk(zclk), .fclk(fclk), .rst_n(rst_n), .zpos(zpos), .zneg(zneg),
.din(d), .dout(dout_ports), .dataout(ena_ports),
.a(a), .iorq_n(iorq_n), .rd_n(rd_n), .wr_n(wr_n), .porthit(porthit),
.ay_bdir(ay_bdir), .ay_bc1(ay_bc1), .border(border),
.p7ffd(p7ffd), .peff7(peff7), .mreq_n(mreq_n), .m1_n(m1_n), .dos(dos),
.vg_intrq(intrq), .vg_drq(drq), .vg_wrFF(vg_wrFF), .vg_cs_n(vg_cs_n),
.idein(idein), .ideout(ideout), .idedataout(idedataout),
.ide_a(ide_a), .ide_cs0_n(ide_cs0_n), .ide_cs1_n(ide_cs1_n),
.ide_wr_n(ide_wr_n), .ide_rd_n(ide_rd_n),
.sd_cs_n_val(zx_sdcs_n_val),
.sd_cs_n_stb(zx_sdcs_n_stb),
.sd_start (zx_sd_start ),
.sd_datain (zx_sd_datain ),
.sd_dataout (zx_sd_dataout),
.keys_in(kbd_port_data),
.mus_in (mus_port_data),
.kj_in (kj_port_data ),
.tape_read(tape_read),
.gluclock_addr(gluclock_addr),
.comport_addr (comport_addr ),
.wait_start_gluclock(wait_start_gluclock),
.wait_start_comport (wait_start_comport ),
.wait_rnw (wait_rnw ),
.wait_write(wait_write),
`ifndef SIMULATE
.wait_read (wait_read ),
`else
.wait_read(8'hFF),
`endif
.atmF7_wr_fclk(atmF7_wr_fclk),
.atm_scr_mode(atm_scr_mode),
.atm_turbo (atm_turbo),
.atm_pen (pager_off),
.atm_cpm_n (cpm_n),
.atm_pen2 (atm_pen2),
.romrw_en(romrw_en),
.pent1m_ram0_0(pent1m_ram0_0),
.pent1m_1m_on (pent1m_1m_on),
.pent1m_page (pent1m_page),
.pent1m_ROM (pent1m_ROM),
.atm_palwr (atm_palwr ),
.atm_paldata(atm_paldata),
.beeper_wr(beeper_wr),
.covox_wr (covox_wr ),
.fnt_wr(fnt_wr),
.clr_nmi(clr_nmi),
.pages(~{ rd_pages[7], rd_pages[6],
rd_pages[5], rd_pages[4],
rd_pages[3], rd_pages[2],
rd_pages[1], rd_pages[0] }),
.ramnroms( rd_ramnrom ),
.dos7ffds( rd_dos7ffd ),
.palcolor(palcolor),
.fontrom_readback(fontrom_readback),
.external_port(external_port),
.set_nmi(set_nmi[1]),
.brk_ena (brk_ena ),
.brk_addr(brk_addr)
);
zint zint(
.fclk(fclk),
.zpos(zpos),
.zneg(zneg),
.int_start(int_start),
.iorq_n(iorq_n),
.m1_n (m1_n ),
.int_n(int_n)
);
znmi znmi
(
.rst_n(rst_n),
.fclk(fclk),
.zpos(zpos),
.zneg(zneg),
.rfsh_n(rfsh_n),
.m1_n (m1_n ),
.mreq_n(mreq_n),
.csrom (csrom ),
.a (a ),
.int_start(int_start),
.set_nmi(set_nmi),
.imm_nmi(imm_nmi),
.clr_nmi(clr_nmi),
.in_nmi (in_nmi ),
.gen_nmi(gen_nmi)
);
zbreak zbreak
(
.rst_n(rst_n),
.fclk(fclk),
.zpos(zpos),
.zneg(zneg),
.m1_n (m1_n ),
.mreq_n(mreq_n),
.a (a ),
.imm_nmi(imm_nmi),
.brk_ena (brk_ena ),
.brk_addr(brk_addr)
);
zwait zwait( .wait_start_gluclock(wait_start_gluclock),
.wait_start_comport (wait_start_comport),
.wait_end(wait_end),
.rst_n(rst_n),
.wait_n(wait_n),
.waits(waits),
.spiint_n(spiint_n) );
wire [1:0] vg_ddrv;
assign vg_a[0] = vg_ddrv[0] ? 1'b1 : 1'b0; // possibly open drain?
assign vg_a[1] = vg_ddrv[1] ? 1'b1 : 1'b0;
vg93 vgshka( .zclk(zclk), .rst_n(rst_n), .fclk(fclk), .vg_clk(vg_clk),
.vg_res_n(vg_res_n), .din(d), .intrq(intrq), .drq(drq), .vg_wrFF(vg_wrFF),
.vg_hrdy(vg_hrdy), .vg_rclk(vg_rclk), .vg_rawr(vg_rawr), .vg_a(vg_ddrv),
.vg_wrd(vg_wrd), .vg_side(vg_side), .step(step), .vg_sl(vg_sl), .vg_sr(vg_sr),
.vg_tr43(vg_tr43), .rdat_n(rdat_b_n), .vg_wf_de(vg_wf_de), .vg_drq(vg_drq),
.vg_irq(vg_irq), .vg_wd(vg_wd) );
// spi2 zspi( .clock(fclk), .sck(sdclk), .sdo(sddo), .sdi(sddi), .start(sd_start),
// .speed(2'b00), .din(sd_datain), .dout(sd_dataout) );
spihub spihub(
.fclk (fclk ),
.rst_n(rst_n),
.sdcs_n(sdcs_n),
.sdclk (sdclk ),
.sddo (sddo ),
.sddi (sddi ),
.zx_sdcs_n_val(zx_sdcs_n_val),
.zx_sdcs_n_stb(zx_sdcs_n_stb),
.zx_sd_start (zx_sd_start ),
.zx_sd_datain (zx_sd_datain ),
.zx_sd_dataout(zx_sd_dataout),
.avr_lock_in (avr_lock_claim),
.avr_lock_out (avr_lock_grant),
.avr_sdcs_n (avr_sdcs_n ),
.avr_sd_start (avr_sd_start ),
.avr_sd_datain (avr_sd_datain ),
.avr_sd_dataout(avr_sd_dataout)
);
//////////////////////////////////////
// sound: beeper, tapeout and covox //
//////////////////////////////////////
sound sound(
.clk(fclk),
.din(d),
.beeper_wr(beeper_wr),
.covox_wr (covox_wr ),
.beeper_mux(beeper_mux),
.sound_bit(beep)
);
endmodule