Top secrets sources NedoPC ngs

Rev

Rev 94 | Blame | Compare with Previous | Last modification | View Log | Download | RSS feed | ?url?

; ports description and include file for NeoGS software projects, v0.3
;
;
; bits degisnation: B_* - bit position (0,1,2,3,4,5,6,7), M_* - bit mask (1,2,4,8,#10,#20,#40,#80)
; C_* - constants to be used
;
;
; part of NeoGS project
;
; (c) 2008 NedoPC


;ZX-side ports

GSCOM   EQU     #BB ;write-only, command for NGS


GSSTAT  equ     #BB ;read-only, command and data bits (positions given immediately below)

B_CBIT  equ     0 ;Command   position
M_CBIT  equ     1 ;       BIT        and mask

B_DBIT  equ     7   ;Data   position
M_DBIT  equ     #80 ;    BIT        and mask


GSDAT   EQU     #B3 ; read-write, data transfer register for NGS

GSCTR   EQU     #33 ; write-only, control register for NGS: constants available given immediately below

C_GRST  equ     #80 ; reset constant to be written into GSCTR
C_GNMI  equ     #40 ; NMI constant to be written into GSCTR
C_GLED  equ     #20 ; LED toggle constant


;GS-side ports

MPAG    equ     #00 ; write-only, Memory PAGe port (big pages at 8000-FFFF or small at 8000-BFFF)
MPAGEX  equ     #10 ; write-only, Memory PAGe EXtended (only small pages at C000-FFFF)

ZXCMD   equ     #01 ; read-only, ZX CoMmanD port: here is the byte written by ZX into GSCOM

ZXDATRD equ     #02 ; read-only, ZX DATa ReaD: a byte written by ZX into GSDAT appears here;
                    ; upon reading this port, data bit is cleared

ZXDATWR equ     #03 ; write-only, ZX DATa WRite: a byte written here is available for ZX in GSDAT;
                    ; upon writing here, data bit is set

ZXSTAT  equ     #04 ; read-only, read ZX STATus: command and data bits. positions are defined by *_CBIT and *_DBIT above

CLRCBIT equ     #05 ; read-write, upon either reading or writing this port, the Command BIT is CLeaRed


VOL1    equ     #06 ; write-only, volumes for sound channels 1-8
VOL2    equ     #07
VOL3    equ     #08
VOL4    equ     #09
VOL5    equ     #16
VOL6    equ     #17
VOL7    equ     #18
VOL8    equ     #19


; following two ports are useless and very odd. They have been made just because they were on the original GS and for that
; strange case when somebody too crazy have used them. Nevertheless, DO NOT USE THEM! They can disappear or even radically
; change functionality in future firmware releases.
DAMNPORT1       equ     #0A ; writing or reading this port sets data bit to the inverse of bit 0 into MPAG port
DAMNPORT2       equ     #0B ; the same as DAMNPORT1, but instead command bit involved, which is made equal to 5th bit of VOL4

LEDCTR          equ     #01 ; write-only, controls on-board LED. D0=0 - LED is on, D0=1 - LED is off
                            ; reset state is LED on.

GSCFG0  equ     #0F ; read-write, GS ConFiG port 0: acts as memory cell, reads previously written value. Bits and fields follow:

B_NOROM         equ     0 ; =0 - there is ROM everywhere except 4000-7FFF, =1 - the RAM is all around
M_NOROM         equ     1

B_RAMRO         equ     1 ; =1 - ram absolute addresses 0000-7FFF (zeroth big page) are write-protected
M_RAMRO         equ     2

B_8CHANS        equ     2 ; =1 - 8 channels mode
M_8CHANS        equ     4

B_EXPAG         equ     3 ; =1 - extended paging: both MPAG and MPAGEX are used to switch two memory windows
M_EXPAG         equ     8

B_CKSEL0        equ     4   ;these bits should be set according to the C_**MHZ constants below
M_CKSEL0        equ     #10
B_CKSEL1        equ     5
M_CKSEL1        equ     #20

C_10MHZ         equ     #30
C_12MHZ         equ     #10
C_20MHZ         equ     #20
C_24MHZ         equ     #00

B_PAN4CH        equ     6  ; =1 - 4 channels, panning (every channel is on left and right with two volumes)
M_PAN4CH        equ     #40

B_INV7B         equ     7 ; =1 - invert 7th bit of samples before putting them to MUL/DAC
M_INV7B         equ     #80





B_SETNCLR       equ     7
M_SETNCLR       equ     #80


SCTRL   EQU     #11   ;Serial ConTRoL: read-write, read: current state of below bits, write - see GS_info

B_SDNCS equ     0
M_SDNCS equ     1

B_MCNCS equ     1
M_MCNCS equ     2

B_MPXRS equ     2
M_MPXRS equ     4

B_MCSPD0 equ    3
M_MCSPD0 equ    8

B_MDHLF equ     4
M_MDHLF equ     #10

B_MCSPD1 equ    5
M_MCSPD1 equ    #20



SSTAT   EQU     #12   ;Serial STATus: read-only, reads state of below bits

B_MDDRQ equ     0
M_MDDRQ equ     1

B_SDDET equ     1
M_SDDET equ     2

B_SDWP  equ     2
M_SDWP  equ     4

B_MCRDY equ     3
M_MCRDY equ     8



SD_SEND EQU     #13 ;SD card SEND, write-only, when written, byte transfer starts with written byte
SD_READ EQU     #13 ;SD card READ, read-only, reads byte received in previous byte transfer
SD_RSTR EQU     #14 ;SD card Read and STaRt, read-only, reads previously received byte and starts new byte transfer with #FF

MD_SEND EQU     #14 ;Mp3 Data SEND, write-only, sends byte to the mp3 data interface

MC_SEND EQU     #15 ;Mp3 Control SEND, write-only, sends byte to the mp3 control interface
MC_READ EQU     #15 ;Mp3 Control READ, read-only, reads byte that was received during previous sending of byte



DMA_MOD EQU     #1B ;select DMA module to work with via DMA_HAD, DMA_MAD, DMA_LAD, DMA_CST ports:

C_DMA_NONE      equ     0 ; none selected
C_DMA_ZX        equ     1 ; ZX module selected
C_DMA_SD        equ     2 ; SD module selected
C_DMA_MP3       equ     3 ; MP3 module selected


DMA_HAD EQU     #1C ; High   DMA ADdress (bits 21:16)
DMA_MAD EQU     #1D ; Middle DMA ADdress (bits 15:8 )
DMA_LAD EQU     #1E ; Low    DMA ADdress (bits  7:0 )
DMA_CST EQU     #1F ; DMA Control and STate



TIM_FRQ         equ     #0E ;timer frequency

C_DEF           equ     #00 ;default 37500 Hz (after reset)
C_DIV2          equ     #01 ;18750 Hz (div by 2)
C_DIV4          equ     #02 ;9375 Hz (div by 4)
C_DIV8          equ     #03 ; etc...
C_DIV16         equ     #04
C_DIV64         equ     #05
C_DIV256        equ     #06
C_DIV1024       equ     #07



INTENA          equ     #0C ;interrupt enables
INTREQ          equ     #0D ;interrupt requests

;bit 7 - B_SETNCLR or M_SETNCLR

B_MP3_DMA_INT   equ     2
M_MP3_DMA_INT   equ     #04

B_SD_DMA_INT    equ     1
M_SD_DMA_INT    equ     #02

B_TIMER_INT     equ     0
M_TIMER_INT     equ     #01


WIN0    equ     #20 ;0000-3fff 16k page (0..255 -- 0..4Mb)
WIN1    equ     #21 ;4000-7fff
WIN2    equ     #22 ;8000-bfff
WIN3    equ     #23 ;c000-ffff