// part of NeoGS project (c) 2007-2008 NedoPC
//
// SPI mode 0 8-bit master module
//
// short diagram for speed=0 (Fclk/Fspi=2, no rdy shown)
//
// clock: ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ (positive edges)
// counter: |00|00|10|11|12|13|14|15|16|17|18|19|1A|1B|1C|1D|1E|1F|00|00|00 // internal!
// sck: ___________/``\__/``\__/``\__/``\__/``\__/``\__/``\__/``\_______
// sdo: --------< do7 X do6 X do5 X do4 X do3 X do2 X do1 X do0 >-------
// sdi: --------< di7 X di6 X di5 X di4 X di3 X di2 X di1 X di0 >-------
// bsync: ________/`````\_________________________________________________
// start: _____/``\_______________________________________________________
// din: -----<IN>-------------------------------------------------------
// dout: old old old old old old old old old old old old old | new new new
//
// data on sdo must be latched by slave on rising sck edge. data on sdo changes on falling edge of sck
//
// data from sdi is latched by master on positive edge of sck, while slave changes it on falling edge.
// WARNING: slave must emit valid di7 bit BEFORE first pulse on sck!
//
// bsync is 1 while do7 is outting, otherwise it is 0
//
// start is synchronous pulse, which starts all transfer and also latches din data on the same clock edge
// as it is registered high. start can be given anytime (only when speed=0),
// so it is functioning then as synchronous reset. when speed!=0, there is global enable for majority of
// flipflops in the module, so start can't be accepted at any time
//
// dout updates with freshly received data at the clock edge in which sck goes high for the last time, thus
// latching last bit on sdi.
//
// sdo emits last bit shifted out after the transfer end
//
// when speed=0, data transfer rate could be as fast as one byte every 16 clock pulses. To achieve that,
// start must be pulsed high simultaneously with the last high pulse of sck
//
// speed[1:0] determines Fclk/Fspi
//
// speed | Fclk/Fspi
// ------+----------
// 2'b00 | 2
// 2'b01 | 4
// 2'b10 | 8
// 2'b11 | 16
//
// for speed=0 you can start new transfer as fast as every 16 clocks
// for speed=1 - every 34 clocks.
// alternatively, you can check rdy output: it goes to 0 after start pulse and when it goes back to 1, you can
// issue another start at the next clock cycle. See spi2_modelled.png and .zip (modelsim project)
//
// warning: if using rdy-driven transfers and speed=0, new transfer will be started every 18 clocks.
// it is recommended to use rdy-driven transfers when speed!=0
//
// warning: this module does not contain asynchronous reset. Provided clock is stable, start=0
// and speed=0, module returns to initial ready state after maximum of 18+8=26 clocks. To reset module
// to the known state from any operational state, set speed=0 and start=1 for 8 clocks
// (that starts Fclk/Fspi=2 speed transfer for sure), then remain start=0, speed=0 for at least 18 clocks.
module spi2(
clock, // system clock
sck, // SPI bus pins...
sdo, //
sdi, //
bsync, // ...and bsync for vs1001
start, // positive strobe that starts transfer
rdy, // ready (idle) - when module can accept data
speed, // =2'b00 - sck full speed (1/2 of clock), =2'b01 - half (1/4 of clock), =2'b10 - one fourth (1/8 of clock), =2'b11 - one eighth (1/16 of clock)
din, // input
dout // and output 8bit busses
);
input clock;
output sck;
wire sck;
output sdo;
input sdi;
output reg bsync;
input start;
output rdy;
input [1:0] speed;
input [7:0] din;
output reg [7:0] dout;
// internal regs
reg [4:0] counter; // governs transmission
wire enable_n; // =1 when transmission in progress
reg [6:0] shiftin; // shifting in data from sdi before emitting it on dout
reg [7:0] shiftout; // shifting out data to the sdo
wire ena_shout_load; // enable load of shiftout register
wire g_ena;
reg [2:0] wcnt;
initial // for simulation only!
begin
counter = 5'b10000;
shiftout = 8'd0;
shiftout = 7'd0;
bsync = 1'd0;
dout = 1'b0;
end
// rdy is enable_n
assign rdy = enable_n;
// sck is low bit of counter
assign sck = counter[0];
// enable_n is high bit of counter
assign enable_n = counter[4];
// sdo is high bit of shiftout
assign sdo = shiftout[7];
assign ena_shout_load = (start | sck) & g_ena;
always @(posedge clock)
begin
if( g_ena )
begin
if( start )
begin
counter <= 5'b00000; // enable_n = 0; sck = 0;
bsync <= 1'b1; // begin bsync pulse
end
else
begin
if( !sck ) // on the rising edge of sck
begin
shiftin[6:0] <= { shiftin[5:0], sdi };
if( (&counter[3:1]) && (!enable_n) )
dout <= { shiftin[6:0], sdi }; // update dout at the last sck rising edge
end
else // on the falling edge of sck
begin
bsync <= 1'b0;
end
if( !enable_n )
counter <= counter + 5'd1;
end
end
end
// shiftout treatment is done so just to save LCELLs in acex1k
always @(posedge clock)
begin
if( ena_shout_load )
begin
if( start )
shiftout <= din;
else // sck
shiftout[7:0] <= { shiftout[6:0], shiftout[0] }; // last bit remains after end of exchange
end
end
// slow speeds - governed by g_ena
always @(posedge clock)
begin
if( speed!=2'b00 )
begin
if( start )
wcnt <= 3'b001;
else if( enable_n )
wcnt <= 3'b000;
else
wcnt <= wcnt + 3'd1;
end
else
wcnt <= 3'b000;
end
assign g_ena = (speed==2'b00) ? 1'b1 :
(speed==2'b01) ? (wcnt[0] == 1'b0 ) :
(speed==2'b10) ? (wcnt[1:0]== 2'b00 ) :
(wcnt[2:0]== 3'b000 ) ;
endmodule